If you are a new angler or you are an experienced angler looking for a new level of excitement, then fishing on a kayak can help you achieve this. Fishing on a kayak has many advantages such as being close to the water so that you can easily net the fish that you are reeling in. However, the problem with fishing on a kayak is that you drift away frequently. This problem has been solved by a kayak fishing anchor. Below are the most commonly asked questions about these anchors.

Do I really need a kayak fishing anchor?

Yes, you do. The reason for this is that you do not want to constantly interrupt your fishing time to readjust the kayak. With a fishing anchor, you can sit in one spot and fish for hours. You do not have to worry about drifting under a dock or somewhere else that you do not want to be.

Are kayak fishing anchors expensive?

When you think about how much benefit, they add to your fishing experience, it is easy to see that these anchors are fairly priced. They say that time is money and these anchors will definitely save you time. They will also reduce your level of stress because you can focus on what really matters during the day, fishing.

What size anchor do I need?

Well, you might need a different size anchor depending on where you will be fishing. If you are going to be fishing in the ocean then you will need a large anchor. This is because the sea is very tumultuous. If you plan on fishing in a lake then you will need a much smaller anchor. This is because the only thing that will be pushing your kayak around in a lake is the wind. Good luck finding the perfect anchor!

Technorati Tags: anchor fishing kayak, anchor fishing kayaks, fishing kayak anchor, fishing kayak anchors, fishing kayaks anchor, kayak anchor, kayak anchors, Kayak Fishing, kayak fishing anchor, kayak fishing anchors

First up, the parts list.  You want to make sure you get the rubber washers for sure.  These keep water out of the boat, and you are drilling holes that could be below the water line.

- 2 Stainless Steel Pulleys or Blocks (Home Depot)

- 2 feet of bungee (sacrificed from the kayak)

- 22 feet of nylon anchor rope

- 2 plastic eyelets or pvc brackets

- 4 stainless steel bolts, washers, and nuts

- 8 rubber washers

- 1 stainless steel caribeaner

First, put the eyelets or pvc brakets onto the kayak where you want them mounted.  Mark the holes with a sharpie, and double check to make sure it is where you want it.  Once you have gotten it dialed in, drill the holes.  Use a bit the same size as the bolt, so you have to force it into the hole.  This helps it seal.

Now, mount the eyelets or pvc brackets to the kayak, using the nuts and bolts.  Put the bolts into the holes in the eyelet.  After this, put a metal washer on, and then a rubber washer.  The rubber washer should be against the kayak, with the metal washer against the eyelet.  Once you have this complete, put the bolts through the holes in the kayak.  Reach in, and put another rubber washer, metal washer, and then the nut.  Tighten it down.  Repeat this for the other end of the kayak.

Now, take the bungee, and cut it in half.  Tie one end to each eyelet, making sure to adjust tension on the bungee while you are tightening it down.  This will help it keep from coming undone.  You should now have 2 pieces of bungee dangling from the side of your kayak, secured to the eyelets.

Now take your stainless steel blocks, or pulleys, and tie another tight knot, securing the bungee to the block.  Make sure to adjust tension as you are tightening, you don’t want this to come loose.  It should start looking like an anchor trolley by now.  Grab your anchor rope, and loop it through both blocks, forming a complete circle with it.

Once you have the anchor rope threaded through the blocks, grab your caribeaner.  Now, all I can recommend is learning how to tie a real knot.  Make sure your caribeaner is attached to both ends of the anchor rope, so you should have a complete circle now, with the caribeaner being between the pulleys.

Go and find a decent anchor, some more anchor rope, a float, and another caribeaner.  Make sure when you attached the actual anchor caribeaner, that you can release it quickly.  Put the float on the end of the anchor rope, so that if you have to release it, you can find it later.  Fish will get tangled up in it if you stay anchored while fighting a fish.

You can also use a stakeout pole through the caribeaner while you are beached to secure the boat in place, and keep the wind from taking it away from you.  So there you have it.  Like I said, future tutorials will be more indepth.  This is just to get you started.

Until next time, I hope you learned something from how to rig an anchor trolley on a sit in fishing kayak, provided by Kayak Fishing Edge

Technorati Tags: anchor rigging kayak, how to build anchor trolley, kayak anchor, kayak anchor rigging, kayak anchor trolley, kayak anchor trolley rigging, Kayak Fishing, Kayak Modifications